Welcome to SP!  -
Areas & RangesMountains & RocksRoutesImagesArticlesTrip ReportsGearOtherPeoplePlans & PartnersWhat's NewForum

AT setup - dynafit/fritschi and size!

Post climbing gear-related questions, offer advice. For classifieds, please use that forum.
 

Re: AT setup - dynafit/fritschi and size!

Postby ExcitableBoy » Thu Mar 29, 2012 1:35 am

I can't comment on the size of the Fritchi's, but I really like my Dynafit binders. Very light, and plenty tough. I weigh as much as 185lbs and ski them moderately hard, not hucking cliffs or anything, and they have held up fine. A swiss mountain guide who has a guiding and ski shop near me and designs skis for K2 said Dynafits were the one binder they got right the first time and didn't screw up.
User Avatar
ExcitableBoy

 
Posts: 2886
Joined: Wed Nov 09, 2005 9:33 am
Location: Issaquah, Washington
Thanked: 424 times in 308 posts

Re: AT setup - dynafit/fritschi and size!

Postby mvs » Thu Mar 29, 2012 2:57 am

I also like my Dynafit bindings a lot. But I've actually got more friends over here (Europe) who don't like them. Two problems:

1) If you've got a bit of snow around the binding holes in your boots it's easy to put them on "wrong" and not know it. The binding will later come off when doing an icy switchback or otherwise placing the ski under oblique pressure. On my particular model (2006) I've learned that the signal for this is that you can't lock the toe binding all the way into x-country mode.

2) Putting the ski back on after a wipe out in deep snow takes effort and patience. In an environment with snow "in everything" the binding will not take as well. Expect to spend 2+ minutes where the Fritchi people need 10 seconds max. My Fritchi friends look at this and just shake their heads.

On the other hand, and this is why I'm a fan despite 1) and 2), the Dynafit bindings are really, really light. I spend a lot more time skinning uphill than dealing with these annoyances. I am happy to optimize for the uphill travel, betraying my real interest in backcountry skis (in other words, I'm a hiker, not a skier).
User Avatar
mvs

 
Posts: 1040
Joined: Tue Oct 23, 2001 7:44 pm
Thanked: 282 times in 108 posts

Re: AT setup - dynafit/fritschi and size!

Postby Kai » Thu Mar 29, 2012 3:48 am

I have skied on Fritschis and Dynafits.

For backcountry, the Dynafits are so much lighter, that I pretty much ski Dynafits exclusively in the BC now.

As far as the reason for getting the smallest bindings possible, smaller bindings weigh less.

I've bent my Dynafit brakes a few cm without any problems. It's pretty common to bend them a bit.
User Avatar
Kai

 
Posts: 700
Joined: Thu Jun 23, 2005 2:26 pm
Location: Salt Lake, Utah, United States
Thanked: 54 times in 40 posts

Re: AT setup - dynafit/fritschi and size!

Postby bfrench » Thu Mar 29, 2012 7:14 am

I would highly recommend not getting fritschis...heavy, breakage issues, and awkward stride. Dynafit bindings have been proven over the last twenty years with basically no changes. People that say they are hard to use or have icing problems obviously haven't spent much time in them. I have skied dynafits for the last nine years with well over 3 million vertical and have never had an issue. I ski aggressively and have no hesitation dropping cliffs in dynafits. Trust me you won't be disappointed. The brakes can be bent out slightly with no problems. Let me know if you have any other questions.
User Avatar
bfrench

 
Posts: 14
Joined: Tue Jan 09, 2007 2:13 am
Location: kalispell, Montana, United States
Thanked: 6 times in 3 posts

Re: AT setup - dynafit/fritschi and size!

Postby coldfoot » Thu Mar 29, 2012 10:47 am

fforcella wrote:
Leaning towards the fritschi's I realized I also have no idea as to which size I should go with. My boots are 26.5 (sole length 300) and the short bindings say they go from 245mm - 300mm. I called a few ski shops in the area and none were very helpful. Diamir says to go with the smallest binding possible (Can anyone explain why that is?). One person said I should go with the medium bindings (280mm - 335mm) in case my feet get bigger/I want to let someone else use my skis. I don't see either of those scenario's playing out but if there is a performance related explanation I'd really like to know.



You probably shouldn't get the small binding if your boots are at the absolute maximum of its capacity. There is some variance in true boot sole length vs marking by a few mm. Or you might decide to get another pair of boots and they have larger sole length for the same size. I would guess that one reason to get the smallest binding you can is because the shorter rail should flex less (if you aren't really big and aggressive this probably isn't a huge issue).

Obviously you need boots with Dynafit fittings to choose the Dynafits, but you probably have that covered already.

Nearly all brakes can be bent out by a little without harm.
coldfoot

 
Posts: 102
Joined: Thu Feb 19, 2009 12:58 am
Location: United States
Thanked: 14 times in 12 posts

Re: AT setup - dynafit/fritschi and size!

Postby ExcitableBoy » Thu Mar 29, 2012 6:26 pm

FWIW, I find my Dynafits much easier to step into than my Silverettas.
User Avatar
ExcitableBoy

 
Posts: 2886
Joined: Wed Nov 09, 2005 9:33 am
Location: Issaquah, Washington
Thanked: 424 times in 308 posts


Return to Gear

 


  • Related topics
    Replies
    Views
    Last post

Who is online

Users browsing this forum: No registered users and 0 guests

© 2006-2013 SummitPost.org. All Rights Reserved.